Chinese translation for "gravity loading"
|
- 重力加载
重力装料
重力装载
自流装载
Related Translations:
- Example Sentences:
| 1. | Representative value of gravity load
重力荷载代表值17 | | 2. | Standard practice for gravity load testing of floors and low slope roofs
楼板和低坡度屋顶重力负荷测试的标准实施规程 | | 3. | The elastic methods are beam - columns method , the pseudo load method , the pseudo lateral load method , the iterative gravity load method and the negative rigidity method
常用弹性分析的方法有：梁柱法、虚拟荷载法、虚拟侧向荷载法、迭代重力荷载法和负刚度法。 | | 4. | Compared with non - slung - load flight , additional aerodynamic load , gravity load should be considered in the slung - load system . so the moment to the gravity center , flight mode and the natural frequency will change
直升机吊挂飞行,与直升机非吊挂飞行状态相比,增加了新的气动载荷、重力载荷,和因此产生的对直升机重心的力矩,其飞行运动模式、低频振荡固有频率均发生改变。 | | 5. | Based on the research of several shiplocks , the temperature and stress field of the lock floor is simulated under temperature and gravity loads , where the shiplock floor is built on different foundations , the effect of setting up wide construction joints is analyzed by the nonlinear finite element method
作者通过对多个船闸工程的研究，结合非线性有限元仿真分析方法，考虑重力、温度等荷载，计算分析土基和岩基上船闸结构底板预留宽缝施工方法的效果。 | | 6. | 2 . dynamics analysis : by setting up jacon matrix differential coefficient sport is passed to descartes space . it makes terminal executing manipulator produce differential coefficient of acceleration and force in every different coordinates can be got . then the effective inertia , coincident inertia and gravity load of two manipulators are calculated by lagrange method . so generalized joint torque of each joint is got , and along with equivalent driving torque , actual driving torque of each joint can be worked out . 3
动力学分析：建立雅可比矩阵将关节空间的各关节的微分运动传递到笛卡尔空间，使末端执行器位姿产生微分运动，以用于求加速度及力在不同坐标系间的线性变换，再用拉格朗日法计算两机械手的有效惯量、偶合惯量、重力载荷，从而计算得到各关节的广义关节力矩，并与等效驱动力矩共同算得各关节的驱动力矩。 | | 7. | Full range in specification " stainless steel tube fittings " come in 500 more varieties and are increasing in number steadily for architects and designers to choose the fittings and parts specification such as 1 , 1 - 14 , 1 - 12 , 2 , 2 - 12 and 3 according to the gravity load requirements . products in pecial specification are available upon your request , we will tailor your need precisely by offering whatsoever specifications you may need
不锈钢圆管组合配件，种类八百多种已开发出五百多种产品规格供建筑师、设计师依其建筑所必须承受之重力，由1 - 14 " 、 1 - 12 " 、 2 " 、 2 - 12 " 、 3 "来选择所需要的圆管大小。 | | 8. | The research result indicated : for the strip primary mirror discussed in this article , the hexagon light - weighted cell has the best structural rigidity quality , the square cell is a little worse , the triangle cell is the worst ; there is an optimum on primary mirror thickness ; on condition of 1g gravity load combining with 4 centigrade uniform temperature rising , the thinner and higher of the flexible support reed , the better of the primary mirror surface figure . the decision of the structural parameters of the flexible support reed must take static rigidity , dynamic rigidity , static strength and dynamic strength of primary mirror assembly into account
研究结果表明：对于本文的长圆形主镜，采用正六边形轻量化孔，镜体结构刚性品质最好，正方形次之，正三角形最差；主镜镜体厚度存在最佳值；主镜组件在1g重力、均匀温升4共同作用的工况下，主镜柔性支撑簧片厚度越小、高度越高，主镜综合面形误差( p - v值)越小，但同时主镜组件的刚体位移增大、固有频率下降，因此柔性支承结构参数的确定要综合考虑主镜的综合面形误差和主镜组件静态刚度、动态刚度、静态强度和动态强度等因素。 |
- Similar Words：
- "gravity knife" Chinese translation, "gravity line" Chinese translation, "gravity lines" Chinese translation, "gravity load" Chinese translation, "gravity loaded accumulator" Chinese translation, "gravity loading type spool" Chinese translation, "gravity logging" Chinese translation, "gravity loss" Chinese translation, "gravity low" Chinese translation, "gravity low, gravity minimum" Chinese translation
|
|
|
